<div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr">Hi everyone,<div><br></div><div>I've some across a bit of a problem and was hoping that someone else here has either experienced it or is able to have a clue as to what is going on.</div><div><br></div><div>I run a Cisco 1841 (a12rtr) here which is my link to the HECnet.  This is established with three GRE tunnels to area 22, 61 and 42.  This router is inside a network that is edged with a Cisco ASA (gatekeeper).  The router a12rtr also has other GRE tunnels and 6in4 tunnels.</div><div><br></div><div>All tunnels are established and traffic is flowing over the ipv4 and ipv6 tunnels without issue.  There is also traffic flowing over the DECnet tunnels as well.  However...</div><div><br></div><div>Despite having adjacencies for the three DECnet routers on the other end of the DECnet tunnels, my routing table is not filling up.</div><div><br></div><div><div>  Area       Cost  Hops           Next Hop to Node       Expires  Prio</div><div>*12            0     0             (Local) -> A12RTR</div><div>  Node       Cost  Hops           Next Hop to Node       Expires  Prio</div><div>*(Area)        0     0             (Local) -> A12RTR</div><div>*BENDER       10     1     FastEthernet0/1 -> BENDER        60</div><div>*TRON         10     1     FastEthernet0/1 -> TRON          99</div><div>*ELYSIM       10     1     FastEthernet0/1 -> ELYSIM      1525</div><div>*A12RTR        0     0             (Local) -> A12RTR</div></div><div><br></div><div><div>a12rtr#show decnet neighbors </div><div>Net Node     Interface            MAC address    Flags</div><div>0   22.1023  Tunnel58             0000.0000.0000 A </div><div>0   42.1022  Tunnel51             0000.0000.0000 A </div><div>0   61.1023  Tunnel53             0000.0000.0000 A </div><div>0   12.2     FastEthernet0/1      aa00.0400.0230 </div><div>0   12.3     FastEthernet0/1      aa00.0400.0330 </div><div>0   12.12    FastEthernet0/1      aa00.0400.0c30 </div></div><div><br></div><div>I can also see that the routers are communicating when I switch on debug:</div><div><br></div><div><div>*Feb 15 04:19:37.007: DNET-ADJ: Endnode hello from 12.3</div><div>*Feb 15 04:19:39.835: DNET-ADJ: Level 2  hello from 42.1022</div><div>*Feb 15 04:19:39.835: DNET-ADJ: Level 2 (IV+) hello from 42.1022</div><div>*Feb 15 04:19:43.207: DNET-ADJ: Endnode hello from 12.2</div><div>*Feb 15 04:19:45.211: DNET-ADJ: Level 2  hello from 61.1023</div><div>*Feb 15 04:19:45.211: DNET-ADJ: Level 2 (IV+) hello from 61.1023</div><div>*Feb 15 04:19:46.315: DNET-ADJ: Level 2  hello from 22.1023</div><div>*Feb 15 04:19:46.315: DNET-ADJ: Level 2 (IV+) hello from 22.1023</div></div><div><br></div><div>So, I am a bit confused as to why there is no routing being exchanged. Is this just a bug and I need to give the router a reboot (it has only been up for 6 days).?</div><div><br></div><div>I did notice this:</div><div><br></div><div><div>a12rtr#show decnet database </div><div>  Area/Node     Cost  Hops           Next Hop to Node       Status</div><div><br></div><div>12               0     0             (Local) -> A12RTR      Active </div><div><br></div><div>22              20     1            Tunnel58 -> 22.1023     Backup </div><div><br></div><div>42              20     1            Tunnel51 -> 42.1022     Backup </div><div><br></div><div>61              20     1            Tunnel53 -> 61.1023     Backup </div><div><br></div><div>BENDER          10     1     FastEthernet0/1 -> BENDER      Active </div><div><br></div><div>TRON            10     1     FastEthernet0/1 -> TRON        Active </div><div><br></div><div>ELYSIM          10     1     FastEthernet0/1 -> ELYSIM      Active </div><div><br></div><div>A12RTR           0     0             (Local) -> A12RTR      Active </div></div><div><br></div><div>The tunnels are all listed as "backup".  I've tried a lot of different things and I'm still experimenting, but I still don't have an answer.  Despite a very long time working with this stuff I've never encountered a situation where the routing table did not populate.</div><div><br></div><div>Any thoughts would be greatly appreciated :-)</div><div><br></div><div>Regards, Tim.</div></div></div></div></div></div>