<div>When I did the VAX station all I did was burn the iso image normally.  The SCSI drive was a Toshiba 4x tray drive with a switch for 512 byte sector support. <br/>
<br/>
Any switch settings on the DEC drive? <br/>
You also should be able to use dd on linux/unix to write the install iso to another scsi disk to see if it boots. <br/>
<br/>
Also--what is the scsi rom error message. <br/>
Is it using the weird DEC scsi cable like the DECstations? <br/>
<br/>
Bill<br/>
<br/>
<font color="#888888"><font color="#888888">Sent from </font><font color="#888888"><a href="mailto:pechter@gmail.com">pechter@gmail.com</a></font></font><br/><br/>-----Original Message-----<br/>From: Supratim Sanyal <supratim@riseup.net><br/>To: hecnet@Update.UU.SE<br/>Sent: Mon, 30 Mar 2020 21:44<br/>Subject: Re: [HECnet] Bringing up a MicroVAX 3100-80<br/><br/></div>On 3/30/20 6:14 PM, G. wrote: <br/>
<br/>
> On Mon, 30 Mar 2020 17:51:21 -0400, Supratim Sanyal wrote: <br/>
> <br/>
>> What is the recommended way to recover from "FILNOTCNTG" error? <br/>
> Boot the system in some other way (cluster satellite, CD-ROM, etc.) and <br/>
> check that SYSBOOT.EXE is contiguous: <br/>
> <br/>
I hooked up the RRD42, burnt the OVMS-7.3 ISO image on a CD-R, and tried  <br/>
to boot dka400, didn't work. The internet is flush with discussions  <br/>
about "special format" CD-ROM, ODS vs ISO, 2048 byte vs 512 byte blocks,  <br/>
etc. <br/>
<br/>
My MacBook refuses to brun the VMS 5.5-2H4 ISO from VAXHAVEN ("invalid  <br/>
disk image"). So basically I have to research and find a way to burn a  <br/>
CD-ROM in the necessary format that will boot the MicroVAX into DCL so  <br/>
that I can repair the CONTIGUOUS issue on DKA100. <br/>
<br/>
I am sure lots of people here have done this - any tips welcome while I  <br/>
am trolling the internet. <br/>
<br/>
KA47-A V1.2-343-V4.0 <br/>
08-00-2B-2D-FF-39 <br/>
24MB <br/>
<br/>
?? 001   9        NI  0172 <br/>
?? 100  10      SCSI  0034 <br/>
<br/>
 >>> <br/>
<br/>
 >>> sh dev <br/>
<br/>
   VMS/VMB      ADDR      DEVTYPE    NUMBYTES     RM/FX WP     <br/>
DEVNAM      REV <br/>
   -------      ----      -------    --------     ----- --     <br/>
------      --- <br/>
   ESA0         08-00-2B-2D-FF-39 <br/>
                A/0/0 <br/>
                A/0/1 <br/>
                A/0/2 <br/>
                A/0/3 <br/>
                A/0/4 <br/>
                A/0/5 <br/>
                A/0/6 <br/>
                A/0/7 <br/>
   DKA100       A/1/0     DISK         1.05GB FX            RZ26L       440C <br/>
   DKA200       A/2/0     DISK         2.10GB FX            RZ28        442C <br/>
   DKA400       A/4/0     RODISK      ......       RM WP    RRD42       4.5d <br/>
  ..HostID..    A/6       INITR <br/>
<br/>
<br/>
<br/>
<br/>
> $ DIR/FULL DKA100:[VMS$COMMON.SYSEXE]SYSBOOT.EXE;0 <br/>
> <br/>
> The "File Attributes" line must show "Contiguous" and hopefully "MoveFile <br/>
> disabled" too. If not, COPY/CONTIGUOUS it to a newer version of the same in <br/>
> the same directory and try the boot again. <br/>
> <br/>
> The other possibility is that the volume is damaged or does not contain a <br/>
> valid VMS file structure. In this case the FILNOTCNTG error is just an <br/>
> indication that VMB.EXE (in ROM) got very confused by your disk's contents. <br/>
> <br/>
> HTH, :) <br/>
> G. <br/>
> <br/>
--  <br/>
Supratim Sanyal, W1XMT <br/>
<a href="tel:3919151">39.19151</a> N, <a href="tel:7723432">77.23432</a> W <br/>
QCOCAL::SANYAL via HECnet <br/>
<br/>