<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
<p>Paul,</p>
<p>Lots of good information. For right now, I did an experiment
and went into <font size="+1"><tt>MDDT</tt></font> and stubbed
out the <font size="+1"><tt>XWD UNLER%,^D5</tt></font> entry in
the <font size="+1"><tt>NIEVTB</tt></font>: table in the running
monitor on VENTI2. Since then (about an hour or so ago), TOMMYT
's ERROR.SYS file has been increasing as usual (a couple of pages
an hour) while VENTI2's hasn't changed at all. So that particular
fire hose is plugged for the time being.</p>
<p>I don't believe I have seen this particular error before,
however, there are probably some great reasons for that. In the
1980's, CCnet may not have had Level-2 routers on it while
Columbia's 20's were online. We did have a problem with the 20's
complaining about long Ethernet frames from an early version BSD
4.2 that was being run on some VAX 11/750's in the Computer
Science department's research lab. They got taught how to not do
that and all was well.</p>
<p>Tops-20's multinet implementation was first done at BBN and then
later imported. I am not sure that it will allow me to change the
frame size. 576 was what was used for the Internet, so I don't
know where that might be hardwired. I'll check.<br>
</p>
<div class="moz-cite-prefix">I think there are two forensics to
perform here:</div>
<div class="moz-cite-prefix">
<ol>
<li>Investigate when the errors started happening; whether they
predate Bob adopting PyDECnet</li>
<li>Investigate what the size difference is; I don't believe
that is going into the error log, but I'll have to look more
carefully with SPEAR.</li>
</ol>
<p>A <b>warning</b> for anyone also looking to track this down:
if you do the retrieve in SPEAR on KLH10 and you don't have have
my time out changes for DTESRV, you will probably crash your
20. This will happen both with a standard DEC monitor and
PANDA.<br>
</p>
</div>
<blockquote type="cite"
cite="mid:06DE0558-38B2-4999-B164-D073D0DEB292@comcast.net">
<hr width="100%" size="2">
<pre class="moz-quote-pre" wrap="">On 1/11/21 4:41 PM, Paul Koning wrote:
</pre>
<blockquote type="cite">
<pre class="moz-quote-pre" wrap="">On Jan 11, 2021, at 4:22 PM, Thomas DeBellis <a class="moz-txt-link-rfc2396E" href="mailto:tommytimesharing@gmail.com"><tommytimesharing@gmail.com></a> wrote:
OK, I guess that's probably a level 2 router broadcast coming over the bridge. There is no way Tops-10 or Tops-20 could currently be generating that because there is no code to do so; they're level 1, only
</pre>
</blockquote>
<pre class="moz-quote-pre" wrap="">
Yes, unfortunately originally both multicasts used the same address. That was changed in Phase IV Plus, but that still sends to the old address for backwards compatibility and it isn't universally implemented.
</pre>
<blockquote type="cite">
<pre class="moz-quote-pre" wrap="">I started looking at the error; it starts out in DNADLL when it is detected on a frame that has come back from NISRV (the Ethernet Interface driver). The error is then handed off to NTMAN where the actual logging is done. So, there are two quick hacks to stop all the errors:
• I could stub out the length error entry (XWD UNLER%,^D5) in the NIEVTB: table in DNADLL.MAC.
• I could put in a filter ($NOFIL) for event class 5 in the NMXFIL: table in NTMAN.MAC.
That will stop the deluge for the moment. Meanwhile, I have to understand what's actually being detected; even the full SPEAR entry is short on details (like how long the frame was).
</pre>
</blockquote>
<pre class="moz-quote-pre" wrap="">
The thing to look for is the buffer size (frame size) setting of the stations on the Ethernet. It should match; if not someone may send a frame small enough by its settings but too large for someone else who has a smaller value. Routing messages tend to cause that problem because they are variable length; the Phase IV rules have the routers send them (the periodic ones) as large as the line buffer size permits.
Note that DECnet by convention doesn't use the full max Ethernet frame size in DECnet, because DECnet has no fragmentation so the normal settings are chosen to make for consistent NSP packet sizes throughout the network. The router sending the problematic messages is 2.1023 (not 63.whatever, Rob, remember that addresses are little endian) which has its Ethernet buffer size set to 591. That matches the VMS conventional default of 576 when accounting for the "long header" used on Ethernet vs. the "short header" on point to point (DDCMP etc.) links). But VENTI2 has its block size set to 576. If you change it to 591 it should start working.
Perhaps I should change PyDECnet to have a way to send shorter than max routing messages.
paul
</pre>
</blockquote>
</body>
</html>