[HECnet] MULTINET + DECnet over ip
Aleš Petan
ales.petan at digital.si
Mon May 4 07:26:08 PDT 2020
Probably the issue is becouse DECNET is not started or no license PAK for UCX/DECNET.
Try $ start/network decnet
Decnet is started in a COM file, located: sys$manager:vmstartup_vms.com
(somewhere at the bottom of the file)
start decnet manualy and then go with citcuits...
regards,
Ales
----- Original Message -----
From: "Serguei" <melehov at sypp.ru>
To: hecnet at Update.UU.SE
Sent: Monday, May 4, 2020 4:21:21 PM
Subject: Re: [HECnet] MULTINET + DECnet over ip
Hi,
Sorry i was in hurry. didn't make it clean enough
Problem that after
@DECNET-CIRCUITS.COM
it says
MultiNet: DECnet not started; not starting DECnet over IP circuits
so seems
multinet set/decnet/remote=pdp-11.online /device=tcpa0: /connect /tcp=connect /buffers=24
not working and
it falls down into error here
If F$GetDVI("_NET0:","EXISTS") Then Goto DECnet_Ok $ Write Sys$Output "MultiNet: DECnet not started; not starting DECnet over IP circuits"
But why? No any other errors occurs
tcpa0: is seen in list of devices
Serg
04.05.2020 17:03, ales.petan at digital.si пишет:
> Have you solved the problem ?
>
>
> -----Original Message-----
> From: owner-hecnet at Update.UU.SE <owner-hecnet at Update.UU.SE> On Behalf Of Serguei
> Sent: Monday, May 4, 2020 8:59 AM
> To: hecnet at Update.UU.SE
> Subject: [HECnet] MULTINET + DECnet over ip
>
> Hello,
>
> I finally won in battle on getting up OpenVMS on simh + multinet 5.4
>
> But now i have problem
>
> part of DECNET-CIRCUITS.COM :
> $ SysGen:=$SysGen
> $ SysGen Load Multinet:TCPDriver
> $ sysgen connect tcpa0:/noadapter/driver=tcpdriver $ multinet set/decnet/remote=X.X.X.X /device=tcpa0: /connect /tcp=connect /buffers=24 $ If F$GetDVI("_NET0:","EXISTS") Then Goto DECnet_Ok $ Write Sys$Output "MultiNet: DECnet not started; not starting DECnet over IP circuits"
> $ Exit
> $DECnet_Ok:
> $ mcr ncp
> set line TCP-0-0 state on
> set circuit TCP-0-0 state on cost 1 hello timer 15
>
> $ @DECNET-CIRCUITS.COM
> MultiNet: DECnet not started; not starting DECnet over IP circuits $ multinet ping pdp-11.online PING PDP-11.ONLINE (X.X.X.X): 56 data bytes
> 64 bytes from X.X.X.X: icmp_seq=0 time=50 ms
> 64 bytes from X.X.X.X: icmp_seq=1 time=50 ms
>
> seems like multinet set/decnet/remote=X.X.X.X /device=tcpa0: /connect /tcp=connect /buffers=24 not creates _NET0: device. but no errors is displayed. Anyone knows what could be problem?
>
> Yours,
>
> Serguei
>
> http://dec-center.ru
>
>
> --
> Это сообщение проверено на вирусы антивирусом Avast.
> https://www.avast.com/antivirus
>
--
Это сообщение проверено на вирусы антивирусом Avast.
https://www.avast.com/antivirus
More information about the Hecnet-list
mailing list