[HECnet] dec repeater 90ts

[Cory Smelosky]

Most likely "not connected"

Sent from my iPhone

> On Dec 4, 2016, at 06:31, john connor <dophini at dir.bg> wrote:
> 
> Thanks guys
> 
> just question 6 pin is N/C what that mean? GND is ground but what is N/C
> 
> and guys does anybody have bn24h rj45-mmj crossover cable to manage this equipment with console? i will buy it.
> 
> thanks,
> VaxCavalera
> 
>> 4 дек. 2016 г., в 13:46, Rob Jarratt <robert.jarratt at ntlworld.com> написал(а):
>> 
>> And I should point out that my notes came originally from Mark Wickens.
>> 
>> Regards
>> 
>> Rob
>> 
>>> -----Original Message-----
>>> From: owner-hecnet at Update.UU.SE [mailto:owner-
>>> hecnet at Update.UU.SE] On Behalf Of Rob Jarratt
>>> Sent: 04 December 2016 10:13
>>> To: hecnet at Update.UU.SE
>>> Subject: RE: [HECnet] dec repeater 90ts
>>> 
>>> It seems that the PSUs often fail, test it with a multimeter. If it is the
>> PSU,
>>> here are my notes on how to make your own mini-DIN PSU connector for a
>>> 90M:
>>> 
>>> Pin        Output
>>> -------------------
>>> 1        +5V
>>> 2        GND
>>> 3        +5V
>>> 4        GND
>>> 5        +5V
>>> 6        N/C
>>> 7        GND
>>> Shield    Tied to chassis ground
>>> 
>>> 
>>> 
>>>        5    6    7
>>>        o    o    o
>>> 
>>>  3  o      [x]     o 4
>>> 
>>>         o      o
>>>         1      2
>>> 
>>> Connector physical pinout looking into the connector on end of cable.
>>> 
>>> Regards
>>> 
>>> Rob
>>> 
>>>> -----Original Message-----
>>>> From: owner-hecnet at Update.UU.SE [mailto:owner-
>>> hecnet at Update.UU.SE] On
>>>> Behalf Of john connor
>>>> Sent: 04 December 2016 05:34
>>>> To: hecnet at Update.UU.SE
>>>> Subject: [HECnet] dec repeater 90ts
>>>> 
>>>> Hi,
>>>> 
>>>> does anybody have schema for dec repeater 90ts and psu h7082-ab for
>>>> standalone work for this repeater
>>>> 
>>>> seems mine repeater died or psu died, need to check
>>>> 
>>>> also how this jack 7pin on psu called and what is signal scheme for
>>>> this
>>> jack
>>>> 
>>>> thanks in advance,
>>>> Serg aka VaxCavalera
>>>> 
>>>>> 26 нояб. 2016 г., в 23:36, Sampsa Laine <sampsa at mac.com> написал(а):
>>>>> 
>>>>> 
>>>>>> On 26 Nov 2016, at 22:32, Brian Schenkenberger, VAXman-
>>>> <system at TMESIS.COM> wrote:
>>>>>> 
>>>>>> G. <gerry77 at mail.com> writes:
>>>>>> 
>>>>>>>> On Sat, 26 Nov 2016 21:26:31 +0200, Sampsa Laine wrote:
>>>>>>>> 
>>>>>>>> Guys, what=E2=80=99s the DCL lexical for extracting the remote
>>>>>>>> host and=
>>>>>>> username of=20
>>>>>>>> someone logged into my system over DECNET? I=E2=80=99m writing
>>> a
>>>>>>>> script=
>>>>>>> that needs=20
>>>>>>>> the host + username of the person connecting to a captive account..
>>>>>>> 
>>>>>>> REMPORT =3D F$GETDVI("TT:","TT_ACCPORNAM") REMNODE =3D
>>>>>>> F$ELEMENT(0,":",REMPORT) REMUSER =3D
>>> F$ELEMENT(2,":",REMPORT)
>>>>>> 
>>>>>> Why not just translate the logicals: SYS$REM_NODE and SYS$REM_ID?
>>>>>> 
>>>>>> $ WRITE SYS$OUTPUT "''F$trnlnm("SYS$REM_NODE")'"
>>>>>> $ WRITE SYS$OUTPUT "''F$trnlnm("SYS$REM_ID")'"
>>>>> 
>>>>> 
>>>>> That does look a lot simpler! Thanks.
>>>>> 
>>>>> Sampsa
>>>>> 
>>>>> 
>> 
>